Published by on August 22, 2021
Categories: Health

FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, 10 Cleaning Cards, 10 Cleaning Pads, 10 cleaning tapes, full instructions. FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, DTC/ Dual hopper; PVC cards “); auto or manual feed. HID GLOBAL, HID, the HID logo, FARGO, and iCLASS, are .. installed and used in accordance with the instruction manual, may cause.

Author: Kirr Gazragore
Country: Chad
Language: English (Spanish)
Genre: Career
Published (Last): 3 September 2013
Pages: 297
PDF File Size: 4.92 Mb
ePub File Size: 15.79 Mb
ISBN: 400-6-14761-906-2
Downloads: 11331
Price: Free* [*Free Regsitration Required]
Uploader: Kazrajar

Loading The Overlaminate The supply end of the overlaminate roll is the side containing the fresh, unused portion of the overlaminate. Selecting the Card Size continued See the previous procedure in this section.

Select this option in conjunction with any application program that supports a multiple-page document, duplex printing. To print the manual completely, please, download it. Remove the two 2 Circuit Board mounting screws located in the Hopper opening. Don’t show me this message again. This print will provide maximum image size, giving complete card coverage on a CR sized card. Ribbons may be ordered individually, or in a case of Page 82 Page 83 – Resolving the incomplete Resin Printing As an alternative to replacing the Main Print Board, the chip U16 can be replaced.

Installing The New Printhead Assembly Extra Cleaning Cards, 50 count. Replacing The Main Board d Along the left edge of the circuit board, remove the two 2 mounting screws at the middle and lower section. Be sure to push down on the cartridge until it clicks into place.


Card Flipper onto the card path or into he Encoder. Do not change this setting.

This square represents the first defined area. If the voltages from the Flipper Home Sensor do not match, replace the Sensor. In the card grid, black indicates the area in which the resin black K panel will be printed.

These arrows below show how the Printhead fits into the mounting bracket. Select Hopper 2 to print only from Hopper 2 in this same fashion. Disconnect the cable connector. Switch Box or the peripheral.

The error log will stop logging errors once it has reached its error occurrence limit of Replacing The Main Board d 3 Circuit Board mounting screws located at the left, middle and right sections. Press the Save button to save any changes that have been changed.

Use this card to confirm that image colors are properly reproduced.

Fargo DTC Thermal Printer Manual & User Guide – Fixya

Measure the total area, and enter those dimensions into the Dimension boxes. See the next page. Insert cards neatly stacked. Resolving the excessive Resin Printing problems continued See the previous procedure in this section. Ensure that the Printer has received data at the speed that it requires.

FARGO Electronics DTC500 Series Troubleshooting Manual

Select Landscape to cause the card to print in a horizontal orientation, as shown on the below. Select Optimized for Photo when printing photo quality images with resin. See Communication Errors on page Firmware Errors Switch Box or peripheral. Printing Process Errors Repair the Ribbon. Repeat steps 1 to 5 until the Magnetic TOF is correct.


Replace the Main Print Board if problem still remains. Card jammed in the Print Station or card flipping area of the Printer. Suggested Retail Prices in U. If a small or low-resolution image is stretched or blown up, a pixilated or grainy effect will occur when printing, as shown below. This position will make it easier to connect the Power and Communication cables.

Continued on the next page. For most applications, the default settings for these options do not need to be changed. Selecting The Lamination Type If the Film Lamination option is selected, the film lamination is applied to the printed card, then the card is ejected. Comments to this Manuals Your Name.

FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers

Print a test card as described in step 1. Using the Card tab Use this option to control specific Printer functions. In most cases, the default settings of these options will suffice. Set the Printer upright carefully. Page 45 – Resolving the Printer not reading Encode Locate the Sensor near the bottom of the Printer. Use this option to change the Printer’s internal settings for controlling the procedures in this section. If problem persists, dc515 with a new Printhead. Resolving the incomplete Resin Printing problems continued See the previous procedure in this section.

Determine if the Main Board is bad.